Post :Junior Instructor(Architectural Assistant) (SR for SC/ST)
Department : Industrial Training Department
Category Code : 466/16
Qualification : SSLC National Trade Certificate in the appropriate Trade,Diploma in the appropriate branch of Engineering
Question Paper Code : 77/2017/OL
Date of Test : 16-09-2017
- The compass observes the angle made by the survey line
- True meridian
- Magnetic meridian
- Arbitrary meridian
- Grid meridian
- V-shaped contours cross a
- Ridgeline
- Valley line
- Saddle
- Pond
- The length of Gunter's chain is
- 100 ft
- 50 ft
- 66 ft
- 76 ft
- The maximum tolerance in a 20 m chain is
- ±2 mm
- ±3 mm
- ±5 mm
- ±8 mm
- Correction due to refraction is given by
- 0.0112 D2
- 0.0785 D2
- 0.0673 D2
- 0.0012 D2
- The chain man who drags the chain is called
- Captain
- Leader
- Follower
- Labour
- The smallest length that can be drawn on a map is
- 0.2 mm
- 0.5 mm
- 10 mm
- 15 mm
- Wingnuts are provided on
- Bubble tubes
- Diaphragm
- Standard
- Tripod
- The lines joining points of equal dip are called
- Aclinic lines
- Isogonic lines
- Agonic lines
- Isoclinic lines
- The object of surveying is to produce a
- Drawing
- Cross-section
- Sketch
- Map
- A level surface is
- a parabolic surface
- an elliptical surface
- a spherical surface
- a plane surface
- For mountainous region, a suitable contour interval may be
- 0.2 m
- 2 m
- 20 m
- 200 m
- Angle between true north and magnetic north is
- Dip
- Declination
- Departure
- Deviation
- Tellurometer is an instrument used for
- GPS
- EMR
- GTS
- EDM
- Three point problem in plane table is a method of
- Resection
- Radiation
- Resolution
- Intersection
- The headroom in a staircase should not be less than
- 3.5 m
- 3 m
- 2.10 m
- 2 m
- The rocks formed due to solidification of molten mass are called
- Aqueous rocks
- Sedimentary rocks
- Metamorphic rocks
- Igneous rocks
- Most economical method of sawing wood is
- Ordinary sawing
- Quarter sawing
- Tangential sawing
- Radial sawing
- Water absorption of vitrified tiles is not more than
- 0.5%
- 1.0%
- 2.0%
- 5.0%
- Purest form of iron is
- Pig iron
- Cast iron
- Wrought iron
- Steel
- Which one of the following does not belong to exogenous tree?
- Deodar
- Pine
- Mahogany
- Bamboo
- Alumina is brick earth gives the bricks
- Resistance to shrinkage
- Plasticity
- Colour
- Strength
- The major constituent of cement is
- Lime
- Silica
- Alumina
- Iron oxide
- Concrete should not be placed by dropping at a height more than
- 400 mm
- 600 mm
- 800 mm
- 1000 mm
- Coefficient of thermal expansion is highest in
- Basalt
- Granite
- Sandstone
- Quartzite
- Which of the following metal is poisonous?
- Copper
- Lead
- Tin
- Aluminium
- Portion of the brick cut across full width is known as
- Queen closer
- King closer
- Mitred closer
- Bat
- Vertical faces of walls meant for fixing door, window or ventilator are known as
- Jambs
- Sills
- Corbels
- Coping
- Steps provided from ground to main entrance in external wall is called
- Threshold
- Stairs
- Pedestal
- Any of these
- Reinforced brick construction is commonly used for
- Walls
- Partition walls
- Compound walls
- Lintels
- The horizontal members of panelled doors are known as
- Styles
- Rails
- Ledges
- Bracings
- The fixture provided on external door for locking is known as
- Tower bolt
- Barred bolt
- Flush bolt
- Aldrop bolt
- Maximum size of coarse aggregate used as a base course in ground floor is
- 12 mm
- 20 mm
- 40 mm
- 50 mm
- Development of fine hair cracks in plastered surface is known as
- Cracking
- Crazing
- Blistering
- Flaking
- If sheets or mastic asphalt are used for damp proofing, the lap should not be less than
- 100 mm
- 125 mm
- 150 mm
- 200 mm
- Which one of the following is a fundamental law of forces?
- Triangle law
- Polygonal law
- Parallelogram law
- Lami's theorem
- If a material has identical properties in all directions, it is said to be
- Homogeneous
- Elastic
- Orthotropic
- Isotropic
- Maximum shear stress in a beam of rectangular cross section is __________ times the average shear stress
- 1.25
- 1.5
- 2.0
- 4.0
- Kern of a rectangular column is having __________ shape.
- Rectangular
- Square
- Diamond
- Triangular
- Section modulus of a triangular cross-section of width b and height h is
- bh2/24
- bh3/24
- bh3/36
- bh2/18
- Minimum number of bars to be provided in a circular column is
- 4
- 6
- 8
- 12
- Which one of the following is not the diameter of market form of reinforcing bar?
- 16 mm
- 18 mm
- 20 mm
- 22 mm
- In the working stress method of R.C.C. design factor of safety used for concrete and steel are respectively
- 3 and 1.85
- 4 and 1.85
- 4 and 2
- 3 and 1.5
- A column is considered long, if the effective length to least lateral dimension is more than
- 10
- 12
- 15
- 18
- Which of the following has high tensile strength?
- Mild steel
- Plain hot rolled wires
- Cold drawn wires
- Thermo mechanically treated bars
- Water tanks should be designed by
- Working stress method
- Ultimate load method
- Limit state method
- Any of these
- Weldability of steel is enhanced by allowing it with
- Carbon
- Sulphur
- Chrome
- Nickel
- The most economical section for a compression member is
- Rectangular
- I-shaped
- Circular
- Hollow circular
- In a residential building, while designing stairs, live load to be taken is
- 3 kN/m2
- 4 kN/m2
- 4.5 kN/m2
- 5 kN/m2
- The angle of contact between mercury and solid surface is
- 0°
- 45°
- 90°
- more than 90°
- The unit of measurement for concrete work in R.C.C. is in
- Sq m
- Cu m
- 10 sq m
- 10 Cu m
- A column that fails due to direct stress, is called
- Short column
- Long column
- Weak column
- Medium column
- For D.P.C at plinth level, the commonly adopted material is
- Bitumen sheeting
- Plastic sheeting
- Cement concrete
- Mastic asphalt
- The construction of a temporary structure required to support an unsafe structure, is called
- Underpinning
- Scaffolding
- Shoring
- Jacking
- Trimmed size of A2 drawing sheet
- 494 × 521
- 594 × 841
- 520 × 594
- 420 × 594
- Which conic is known as "central conic"?
- Ellipse
- Circle
- Parabola
- Hyperbola
- Which one is not a conic section?
- Ellipse
- Parabola
- Hyperbola
- Circle
- T-square is used for drawing
- Inclined lines
- Curved lines
- Horizontal lines
- Vertical lines
- Visual ray method is used for drawing _________ projection.
- Perspective
- Isometric
- Oblique
- Orthographic
- The angle of a miter line is __________ degrees.
- 75
- 60
- 45
- 30
- A byte consists of __________ bits.
- 64
- 32
- 16
- 8
- The file extension of a drawing template is
- .dwg
- .dxf
- .dws
- .dwt
- F9 is the short key of __________.
- ORTHO
- SNAP
- OSNAP
- POLAR
- __________ is the command used in convert polyline to line.
- Explode
- Join
- Extent
- Extreme
- 'XL' is the shortcut key of
- Erace
- Hatch
- Construction line
- Scale
- The behaviour of concrete under instantaneous loads is
- Elastic
- Plastic
- Anelastic
- Visco-elastic
- Separation of ingredients from concrete during transportation is known as
- Bleeding
- Creep
- Segregation
- Shrinkage
- Durability of cement concrete generally improves by
- Addition of sand
- Addition of cement
- Vibrations
- Additions of coarse aggregate
- The ratio of Young's modulus of elasticity for steel to that for concrete is known as
- Specific ratio
- Modular ratio
- Poisson's ratio
- Elasticity ratio
- The fineness modulus of fine aggregate is in the range of
- 7.0 to 10.0
- 5.0 to 7.0
- 3.5 to 5.0
- 2.0 to 3.5
- Shrinkage in concrete increases its
- Tensile strength
- Flexural strength
- Bond strength
- Shear strength
- The deflection at any section of a beam is __________ of the corresponding section of the conjugate beam.
- Shear force
- Bending moment
- Deflection
- Slope
- The rate of change of bending moment is equal to
- Shear force
- Deflection
- Slope
- Poisson's ratio x deflection
- The density of cement is generally
- 1500 kg/m3
- 1750 kg/m3
- 1250 kg/m3
- 2000 kg/m3
- A member subjected to tensile stresses is known as
- Principal rafter
- Purlin
- Strut
- Tie
- The ratio of moment of inertia of a rectangle about its centroidal axis to the moment of inertia about its base
- 2
- 3/4
- 1/2
- 1/4
- The maximum bending moment of a simply supported beam of span l and carrying a point load W at the centre of the beam is
- Wl/4
- Wl/2
- Wl
- Wl2/4)
- In slabs and beams creep is responsible for
- Bending
- Deflection
- Cracking
- Shrinkage
- In theory of simple bending, the bending stress in the beam section varies
- Parabolically
- Elliptically
- Linearly
- None of them
- In architecture design, the absence of monotony is called
- Proportion
- Balance
- Contrast
- Rhythm
- When was the preamble to the constitution of India first amended?
- 1951
- 1971
- 1976
- Never
- The recipient of 'Jnanpith Award' in the year 2016
- Mahasweta Devi
- Shankha Ghosh
- Reghuveer Chaudhari
- Bhalchandra Nemada
- The Portuguese established printing in Kerala in the year
- 1577
- 1498
- 1502
- 1524
- Autobiography 'Ente Vazhithiruvu' belongs to
- M.C. Joseph
- T.R. Krishnaswami Iyer
- Makthi Thangal
- Ponkunnam Varkey
- The idea of an elected President at the head of the Parliamentary system, India borrowed from
- United States of America
- Ireland
- Australia
- Canada
- The year of Paliyam Sathyagraha
- 1946
- 1943
- 1948
- 1931
- The States Reorganisation Act created _______ states and _______ Union territories.
- 14:6
- 14:7
- 13:6
- 13:5
- The ordinance issued by the governor are subject to approval by
- Parliament
- State legislature
- President
- None
- Samathwa Samajam founded by
- Swami Vagbhatananda
- K.P. Vellon
- Brahmananda Sivayogi
- Vaikunta Swami
- The modified form of 'Right To Information Act' passed on
- February 2000
- February 2011
- February 2012
- February 2013
- How many types of emergencies has the constitution envisaged
- One
- Two
- Three
- Four
- World Environment Day theme for 2017
- Connecting people to nature
- Only one earth
- One world one environment
- Save earth from pollution
- The first recipient of Vayalar Sahithya Puraskaram
- Anna Chandi
- Lalithambika Antharjanam
- Parvathi Nenmenimangalam
- Akkamma Cheriyan
- Prathyaksha Raksha. Daiva Sabha founded in the year ________ by Poikayil Youhannan.
- 1948
- 1923
- 1909
- 1917
- Herman Gundert, member of Basel-Evangelical mission started the newspaper
- Paschimodayam
- Deepika
- Prabhatham
- Vivekodayam
- The slogan 'Travancore for Travancorean's was related to
- Temple Entry Proclamation
- Ezhava memorial
- Abstention movement
- Malayalee memorial
- Founder editor of the newspaper 'Kerala Kaumudi'
- C. Kesavan
- C.V. Kunjaraman
- P. Krishna Pillai
- Barrister G.P. Pillai
- Kerala Sahithya Academy President
- Vysakhan
- M. Santhosh Kumar
- George Onakkoor
- Palliyara Sreedharan
- The organization 'Sugunavardhini' was formed by
- Thycaud Ayya Vaikundar
- Pandit K.P. Karuppan
- Dr. Ayyathan Gopalan
- Moorkoth Kumaran
- Vayanadinam or Day of reading is observed on
- January 19
- July 19
- July 29
- June 19
0 Comments