Post : Computer Gr. II
Department : Printing
Category Code : 352/16
Qualification : SSLC + Diploma in Printing Technology
Question Paper Code : 75/2017
Date of Test : 28-06-2017
- Lithography was invented by__________.
- Alois Senefelder
- Richard Kevenski
- Ira Rubel
- Davis Ronaldo
- Image area and non-image areas are the same Planographic level in __________ Printing process.
- Letterpress
- Lithography
- Gravure
- Intaglio
- The __________ are used in the densitometer for reducing the measurement differences between wet and dry samples especially with coated papers.
- Blue filter
- Patch filter
- Polarizing filters
- Green filter
- The range of colours that can be viewed, displayed or printed is known as __________.
- Colour triad
- Colour gamut
- Colour diad
- Complementary colour
- The device used to converts postscript graphics and text into high resolution bit-mapped image is called __________.
- Raster image processor
- Film processor
- Rapid access processor
- Lith processor
- __________ uses data base-driven print files for the mass personalization of printed materials.
- Ink jet data printing
- Laser data printing
- Variable data printing
- Excel sheet data printing
- A printing press, that allows the simultaneous printing on both sides in a single pass through press is called __________.
- Perfecting
- Duplicating
- Stenciling
- Double side printing
- The device used to force the ink through the screen mesh and stencil on to the printing stock below is called __________.
- Doctor blade
- Squeegee
- Silkscreen
- Ink Knife
- A narrow gap between body of the plate cylinder and the bearer is called __________.
- Bevels
- Undercut
- Gutter
- Cylinder gap
- The originals in which detail and tone values are represented by a series of evenly spaced dots of varying size and shape is known as __________.
- Continuous tone originals
- Halftone originals
- Line originals
- Printed originals
- The values for yellow, magenta, and cyan that produce a neutral gray with no dominant when prints at a normal density is called __________.
- Under colour removal
- Gray colour removal
- Gray balance
- Colour cast
- __________ is the hardened metal ring attached to the both ends of a cylinder body in the printing unit of an offset printing machine.
- Beating
- Bearer
- Cam
- Gear
- The cold set web offset machine printing inks dries through __________ into the paper.
- Oxidation
- Absorption
- Evaporation
- Perspiration
- The device used to rewinds the printed web back into roll form is called __________.
- Roller top former
- Reel stand
- Reel splicer
- Rewinder
- __________ is the name given to a specific colour, to differentiate it from any other.
- Saturation
- Tint
- Shade
- Hue
- The ability of a wet, printed ink film to accept another wet ink film printed over, it is called __________.
- Wet trapping
- Dry trapping
- Trapping
- None of these
- __________ is the process of printing directly from a printing plate to a substrate.
- Lithography
- Direct lithography
- Direct imaging
- Collotype printing
- In photomechanics, exposure from a second negative or flat superimposed on an exposed image of a previous negative or flat is called __________.
- Tint
- Surprint
- Reverse
- Overprint
- __________ technology created printed documents with streams of ink drops that are deflected to the substrate based on information in digital files.
- Inkjet
- Electrophotography
- Iconography
- Laser printer
- __________ is form of additive manufacturing technology where a three dimensional object is created by laying successive layer of material.
- 3D printing
- Lenticular printing
- Hologram printing
- Flexographic printing
- A halftone dot, negative or positive characterized by a sharp, clean cut edge is called__________.
- Soft dot
- Hard dot
- Round dot
- Elliptical dot
- __________ cam is a circular cam in which the rotary shaft is off center.
- Eccentric
- Tow and wipe
- Cylindrical
- Disc
- __________ is an instrument used for taking external dimensions up to an accuracy of 0.01 mm.
- Micrometer
- Wrenches
- Vernier caliper
- Feeler gauge
- In an offset printing press, the image carrier is imaged directly on the press with built in laser exposure is called __________.
- Computer to print
- Direct imaging
- Computer to plate
- Computer to conventional plate
- The length of time that the ductor roller contacts the fountain roller is called __________.
- Transfer time
- Dwell time
- Contact time
- Pick time
- The instrument used to measure the hardness of roller compound is called __________.
- Colorimeter
- Durometer
- Densitometer
- Spectrophotometer
- In an offset machine __________ are series of three to five rollers that contact printing plate and transfer ink to it.
- Former rollers
- Oscillating rollers
- Form rollers
- Duct rollers
- A __________ is small spot of imperfection that appears in print on images or flat tints.
- Ghosting
- Halo
- Hickey
- Blinding
- Reproduction of a continuous tone image that consists of two half tone printed in register is called __________.
- Triton
- Dual tone
- Duotone
- Triple tone
- A __________ the first roller in the roller train alternatively contacts the fountain roller and an oscillating roller, transferring a set amount of ink.
- Ductor roller
- Form rollers
- Transfer rollers
- Former
- In offset printing machine __________ occurs when the metal oscillating rollers lose their affinity for ink and fail to carry it.
- Plate blinding
- Roller stripping
- Excess inking
- Thinning of rollers
- An instrument that measures and compares the hue, purity, and brightness of colors in a manner that simulates how people perceive color is __________.
- Spectrophotometer
- Colorimeter
- CIE - Lab meter
- Transmission densitometer
- In color reproduction, the __________ plate is generated to increase contrast of dark tones and make them appear neutral.
- Black Plate
- Magenta Plate
- Gray Plate
- Cyan plate
- The device used in drum scanners to digitize images at very high resolutions__________.
- Charged couple device
- Light sensors
- Laser beam heads
- Photomultiplier tubes
- A specially prepared image to which the lens is attached is called __________.
- Direct image
- Laser image
- Lenticular image
- Lens image
- A process by which a scanner, monitor, or output device is adjusted to provide a more accurate display and reproduction of image is called __________.
- Calibration
- Gama adjustment
- Contrast adjustment
- Exposure adjustment
- The positioning of film negatives or positives on a flat to imposed layout for plate making iscalled __________.
- Layout assembly
- Paste up
- Stripping
- Imposition
- To create a continuous operation, large companies that handle repetitive type of job like book work or magazines attach finishing equipment to the press is called __________.
- On-line finishing
- In-line finishing
- Perfect finishing
- Automatic finishing
- A folding unit, paper fold by means of a thin knife blade that forces a sheet of paper between two rotating rollers is called __________.
- Knife folding
- Buckle folding
- Parallel fold
- Accordion fold
- To make a __________ , first fold a sheet across its length, then make a second fold at right angle to the first across the sheet width.
- French fold
- Parallel fold
- Zig Zag fold
- Cross fold
- A process that uses a solid strip of hardened steel to crush the grain of the paper to create a straight line for folding is called __________.
- Perforating
- Creasing
- Embossing
- Stamping
- A large single sheet is frequently passed through a printing press and then folded and trimmed to form portion of book is called __________.
- Signature imposition
- 3-up imposition
- 2-up imposition
- Ganged imposition
- The __________ represents the masking sheet area used to clamp the lithographic plate to the press cylinder.
- Cylinder line
- Centerline
- Gripper line
- Plate margin line
- Smearing of trailing edges of dots, resulting ink film tapering into the white areas is called __________.
- Slur
- Ink spread
- Doubling
- Ghosting
- __________ causes a halftone dot to grow in all directions.
- Dot loss
- Dot gain
- Dot enlarging
- Dot reduction
- A very smooth, hard, glossy surface is created when the pores of the blanket fill with ink, ink solvent, and gum known as __________.
- Glaze
- Gloss
- Mottle
- Ghosting
- The name of the technology uses to transmit a higher number of bytes over standard twister pair cable is __________.
- Integrated service digital network
- Digital subscriber line
- T - carrier line
- Asynchronous transfer mode
- Electrostatic printing was invented by __________.
- Chester Carlson
- Ira Rubel
- Malcolm Guentert
- William Wolfgang
- The distance from belly to back side is the __________ of the piece of foundry type.
- Set width
- Point size
- Type-height
- Height to paper
- A __________ is an internal curve between the serif stroke and the main stroke.
- Fillet
- Stress
- Descender
- Ascender
- __________ is defined as the vertical distance between one baseline and the next, measured in points.
- Character spacing
- Line spacing
- Set width
- Point size
- A one colour reproduction printed on a coloured sheet is known as __________.
- Fake colour
- Spot colour
- Process colour
- Tint
- __________ is the process of confirming that the digital files required for the printing process are all present, valid, correctly formatted, and of the desired type.
- Postflighting
- Preflighting
- Perfecting
- Ripping
- The density of transparent material is measured by light passing through the base with a device is called __________.
- Transmission densitometer
- Photo spectrometer
- Transparent densitometer
- Colorimeter
- __________ is measured in terms of percentage of ink coverage.
- Dot shape
- Dot size
- Dot gain
- Dot loss
- The magenta separation negative is made by using __________ filter.
- Red filter
- Green filter
- Blue filter
- Yellow filter
- __________ proofs remade using the same type of ink and paper that used on the final job.
- Digital proofs
- Press proofs
- Photomechanical proofs
- Diazo proofs
- Resolution in a scanner refers to the number of __________.
- Dots per linear inch
- Pixel per linear inch
- Colours per linear inch
- Density per linear inch
- In digital typography, subtracting space between a group of letters, applied to all the letters using the same value is known as __________.
- Kerning
- Tracking
- Leading
- Formatting
- The method by which you align your four colour half tone screen is referred to as the__________.
- Screen angle
- Screen ruling
- Resolution
- Screening
- __________ is a lithographic process that does not use fount solution.
- Direct imaging
- Waterless
- Water based
- Waterbuses
- Certain physic-chemical effects permit heat to produce a reversible color change in multilayered polymeric materials is called __________.
- Reusable paper
- Recycle paper
- E-paper
- Rewritable paper
- The paper has high grease resistance and wet strength due to sulphuric acid bathing and gelatinization is called __________.
- Vegetable parchment
- Leather parchment
- Art paper
- Coated paper
- A liquid coating applied to a printed surface to enhance the appearance of printed photographs in brochures is called __________.
- Lamination
- Wet lamination
- Varnish
- Dry lamination
- A __________ is an optical machine-readable representation of data.
- Variable data
- Barcode
- Address code
- MICR code
- __________ is a method of packaging by which thin, clear, plastic is shrunk on the object backed by printed card.
- Tetra pack
- Blister packaging
- Skin packaging
- Strip packaging
- The other name of the CIC presses the four printing units or more then this press is called as __________.
- Blanket to blanket press
- Stack type press
- Inline press
- Satellite press
- __________ is the problem caused due to the formation of wet ink of the first printed sheet at the back side of the second printed sheets.
- Set-off
- Blinding
- Scumming
- Roller stripping
- The devices present over the feed board for control the transportation of sheet before the first printing unit is called __________.
- Bosses
- Skeleton wheels
- Double sheet detector
- Friction feeder
- The __________ solution is used in the fountain solution to desensitize the non image area of the plate.
- Magnesium Nitrate
- Fungicide
- Gum Arabic
- Isopropyl Alcohol
- __________ is the term to determine the amount of ion present in the dampening solution.
- pH value
- Density
- Conductivity
- Viscosity
- The __________ is present at one side of the cylinder which is used to generate power for driving other cylinders.
- Bearing
- Gear
- Cam
- Bearer
- __________ is used to increase the contact angle and reduce the surface tension of water during the use of dampening solution.
- Isopropyl Alcohol
- Magnesium Nitrate
- Corrosion inhibitors
- Gum Arabic
- In web offset machines __________ is to maintain the flow rate and to control the web tension.
- Metering roller
- Splicer
- Dancer roller
- Turn bars
- In flexography inks dry by __________ of solvents.
- Absorption
- Evaporation
- Oxidation
- Crystallization
- An instrument that exposes a step tablet onto light sensitive material is called__________.
- Sensitometer
- Densitometer
- Star target
- Colour control bar
- The design characteristic concerned with size relationship of both sheet size and image placement is called __________.
- Harmony
- Proportion
- Balance
- Unity
- An image in which the elements are represented by mathematical equations is called__________.
- Vector
- Raster
- Photograph
- Painting
- The process and path that a job takes through the production process from start to finish is known as __________.
- FTP
- OPI
- Workflow
- Job flow
- White portion of a photograph with no detail, such as bright, shiny reflection from a metal object is called __________.
- Spectral highlight
- Highlight
- Shadow
- Spectral reflection
- The Northern most ranges of the Himalayas is __________.
- Himadri
- Himachal
- Siwalik
- Sahyadri
- Badarinath, the pilgrim centre is at __________ Indian state.
- Uttar Pradesh
- Madhya Pradesh
- Uttarakhand
- Maharashtra
- The South - West Monsoon comes in :
- October to November
- June to August
- May to July
- November to January
- The aim of the fifth five year plan was :
- Industrial development
- Removal of poverty
- Human resource development
- Increase in investment
- The Parambikulam wildlife Sanctuary is at :
- Idukki
- Wayanadu
- Kannur
- Palakkad
- The most fertile region of India is :
- The Himalayan region
- The central highland
- The Indo-Gangetic plain
- The peninsular plateau
- During freedom struggle who said, “Give me blood, I will give you freedom”?
- Subash Chandra Bose
- Mahatma Gandhi
- Jawaharlal Nehru
- Bhagat Singh
- Name the place where the historic congress session held in 1929 and demanded “Poorna Swaraj”.
- Lahore
- Lucknow
- Surat
- Delhi
- The “Abhinav Bharat Society” was founded by :
- Gopala Krishna Gokhale
- Swamiji Krishna Varma
- Annie Besant
- V.D. Savarkar
- Name the Mughal emperor who was proclaimed as “Shahen-Shah” of Hindustan by the rebels of 1857.
- Akbar
- Bahadurshah
- Aurangazeb
- Shahjahan
- Who organised the famous “Kallumala Agitation”?
- Chattampi Swamikal
- Kumaranasan
- V.T. Bhattatiripad
- Ayyankali
- Who is the father of Kerala-Renaissance?
- Kumara Guru
- Mannathu Padmanabhan
- Sree Narayana Guru
- Sri Chitira Tirunal
- Who founded “Atma Vidya Sangham”?
- Poikayil Yohannan
- Vaghbhatananda
- C. Kesavan
- Vakkom Abdul Khader Moulavi
- The Ezhava memorial was presented in 1896 to Sri. Mulam Tirunal under the leadership of __________.
- A.K. Gopalan
- Dr. Palpu
- T.K. Madhavan
- K. Kelappan
- The movement started by Vaikunda-Swamikal was :
- Samatva Samajam
- Sadhujana Paripalana Yogam
- Sahodara Sangham
- Vidhya Poshini Sabha
- Who won the Australian Open 2017 for Women?
- Venus Williams
- Marta Kostyuk
- Serena Williams
- Lucie Safarova
- __________ is crowned as Miss Universe of 2017.
- Iris Mittenaere
- Raquel Pelissier
- Roshmitha Harimurthy
- Andrea Tovar
- The present U.N. Secretary General is :
- Kofi Annan
- Ban Ki Moon
- Xi Jinping
- Antonio Guterres
- Who among the following won Padmavibhushan of 2017?
- Chemanchery Kunhiraman Nair
- P.R. Sreejesh
- K.J. Yesudas
- Akkitham
- The 20th National Conference on e-governance was held at :
- Pune
- Mumbai
- Calcutta
- Visakhapatnam
0 Comments